Posts by Don Rogers

Don Rogers 2003-05-05 22:41:15 UTC Hardware/Software compatability Don Rogers 2003-05-06 17:00:14 UTC RE:Help putting together Power Supply Don Rogers 2003-05-12 22:19:45 UTC Re:Threading of CNC Don Rogers 2003-05-12 22:20:33 UTC Re: Vinyl cutting knife in place of router Don Rogers 2003-05-14 19:43:01 UTC Re:Guides Don Rogers 2003-05-14 20:59:37 UTC Re:Lead screws Don Rogers 2003-05-18 10:45:52 UTC Re:Alternative shafts for linear bearings Don Rogers 2003-05-18 18:41:36 UTC Re:creating toolpath (cutting stones) Don Rogers 2003-06-05 23:10:02 UTC Re: Re: Sound proof box Don Rogers 2003-06-12 16:50:32 UTC Re:Tac sensors Don Rogers 2003-06-24 22:53:16 UTC Re: servo motor shaft 5/8 to 1/4...best way?? Don Rogers 2003-06-24 22:53:16 UTC BDI EMC Install problem Don Rogers 2003-06-25 09:12:58 UTC Re: BDI EMC Install problem Don Rogers 2003-06-27 20:24:02 UTC Re: Jig transit, aligning ways Don Rogers 2003-07-08 10:08:48 UTC Re: Parallel Port to Power Supply Grounding Differential Don Rogers 2003-07-11 12:25:24 UTC Re:CNC vs HOT WEATHER, WHAT TO DO?? Don Rogers 2003-07-14 10:10:27 UTC Re: [CAD_CAM_EDM_DRO] Digest Number 3232 Don Rogers 2003-07-15 22:33:17 UTC Re: Question about AC power distribution in CNC controller box Don Rogers 2003-07-22 09:00:08 UTC Re: EMC iso image Don Rogers 2003-08-01 21:32:53 UTC Re:230 volt power Don Rogers 2003-08-04 23:09:58 UTC Re: 230 volt power Don Rogers 2003-08-06 20:23:36 UTC Re: motor cables connection Don Rogers 2003-08-06 22:25:21 UTC Re:Which to trust, home-built DROs or hash marks? Don Rogers 2003-08-09 10:47:55 UTC Re: motor cables connection in Digest Number 3280 Don Rogers 2003-08-12 21:47:37 UTC Re: Controller setup for Taig cnc ready mill Don Rogers 2003-08-22 16:13:48 UTC Re: [CAD_CAM_EDM_DRO] Digest Number 3311 Don Rogers 2003-09-30 17:06:03 UTC Treadmotor speed control for power supply. Don Rogers 2003-10-29 21:54:29 UTC re:Crashing CNCs: what gives ? Don Rogers 2003-11-04 21:22:28 UTC repeatable vs accurate switch Don Rogers 2003-11-04 21:27:38 UTC Re: e-bay type feedback Don Rogers 2003-11-04 22:36:02 UTC Re: serial vs parallel port Don Rogers 2003-11-04 22:41:05 UTC Re: [CAD_CAM_EDM_DRO] Digest Number 3452 Don Rogers 2003-11-05 22:46:13 UTC Re: serial vs parallel port Don Rogers 2003-11-06 08:38:38 UTC Re: repeatable vs accurate switch Don Rogers 2003-11-06 08:42:46 UTC Re: repeatable vs accurate switch Don Rogers 2003-11-06 09:25:59 UTC Re: repeatable vs accurate switch Don Rogers 2003-11-10 18:34:49 UTC Re: making an ali flexible coupler Don Rogers 2003-11-11 11:19:08 UTC Re: [CAD_CAM_EDM_DRO] Digest Number 3465 Don Rogers 2003-11-11 11:26:38 UTC Re:making an ali flexible coupler Don Rogers 2003-11-13 22:35:53 UTC Auto Cad Documentation (AD?) Don Rogers 2003-11-17 08:41:46 UTC Re:Insulating D-shell from chassis Don Rogers 2003-11-20 20:07:08 UTC Re:More on Re: Insulating D-shell from chassis? Don Rogers 2003-11-21 22:33:45 UTC Re:More on Re: Insulating D-shell from chassis? Don Rogers 2003-11-21 22:38:28 UTC Re: scams Don Rogers 2003-12-11 23:11:54 UTC Re: Hexapod question Don Rogers 2003-12-15 23:13:17 UTC Re: Harbor Freight 47052 to CNC Don Rogers 2003-12-16 22:29:50 UTC Re: Free Prodesktop Express ending4 Don Rogers 2003-12-18 22:18:11 UTC Re:Rhino3D + Visual mill Don Rogers 2004-02-04 10:40:11 UTC Re:18 ft. router Don Rogers 2004-02-11 13:08:59 UTC Re: Powermax II voltage rating? Don Rogers 2004-02-12 21:50:08 UTC Balancing drivers to motors Don Rogers 2004-02-26 21:27:41 UTC Re: [CAD_CAM_EDM_DRO] Digest Number 3654 Don Rogers 2004-03-09 14:59:41 UTC Re: NEW CAD/CAM SYSTEM Don Rogers 2004-03-09 23:15:06 UTC Re: [CAD_CAM_EDM_DRO] Digest Number 3677 Don Rogers 2004-03-18 09:06:57 UTC Re: Controllers Don Rogers 2004-04-21 22:27:53 UTC Re:Visual Mill vs Visual Mill Basic questions Don Rogers 2004-04-23 16:27:54 UTC Re: spindle plans Don Rogers 2004-04-27 15:32:42 UTC Re: What is the weak link in machine precision? Don Rogers 2004-04-30 23:27:55 UTC Re: Canned Cycle was G_Code sharing Don Rogers 2004-07-27 15:04:14 UTC Re: Parker SX stepper motor drives and EMC Don Rogers 2004-09-02 12:33:50 UTC 3 Phase Power safety and information File uploaded Don Rogers 2004-09-04 22:37:01 UTC Re: Re: part holding Don Rogers 2004-10-18 16:15:58 UTC Re: Gecko burned out Don Rogers 2004-10-20 17:57:14 UTC Serial Port to Calipers Don Rogers 2004-10-22 14:10:54 UTC Re: Serial Port to Calipers Don Rogers 2004-10-26 11:46:48 UTC Re: HP plotter servo